Forum:

gear

Makita battery chainsaw won’t light up

John F Dean

master steward

Posts: 8738

Location: southern Illinois, USA

3622

I like...

posted 9 months ago

6
Number of slices to send:

Optional 'thank-you' note:

Send

I have a 36v Makita chainsaw that won’t light up or start. I have recharged and traded out the batteries….still no results. I am heading outside after I post this to clean off the contact points.

Any other ideas?

I figure if someone from the future hasn’t tried to stop me, I can’t be messing up that bad.

Les Frijo

Posts: 254

posted 9 months ago

8
Number of slices to send:

Optional 'thank-you' note:

Send

I'm not familiar with these but Makita stuff is usually quite tough. Maybe being a chainsaw it is subject to oils and resins flying around and could be the cause. Hopefully cleaning the contacts works. My only other idea is a few good Fonzis to see if something is loose inside and then maybe cleaning everything you can with an electrical component safe spray.

Check that the safety guard/brake is not engaged.

FFS

thomas rubino

master rocket scientist

Posts: 7136

Location: latitude 47 N.W. montana zone 6A

4284

I like...

posted 9 months ago

7
Number of slices to send:

Optional 'thank-you' note:

Send

At my house, once they stop lighting up, and the batteries are known to be good, it's dead.
Of course, you can double- or triple-check all the usual stuff, but you already did that before writing.
I hope the repair cost is reasonable, but my experience has been ... that it is cheaper to buy a new one.

For all your Montana Masonry Heater parts (also known as) Rocket Mass heater parts.
Visit me at
dragontechrmh.com Once you go brick you will never go back!

John F Dean

master steward

Posts: 8738

Location: southern Illinois, USA

3622

I like...

posted 9 months ago

8
Number of slices to send:

Optional 'thank-you' note:

Send

Hi Thomas,

I just cleaned the contact points really well … no success, seeing that I have 2 Greenworks …I will let this one RIP. I was hoping for a hidden breaker I didn’t know about.

I figure if someone from the future hasn’t tried to stop me, I can’t be messing up that bad.

Christopher Weeks

gardener

Posts: 6592

Location: Carlton County, Minnesota, USA: 3b; Dfb; sandy loam; in the woods

4012

I like...

posted 9 months ago

7
Number of slices to send:

Optional 'thank-you' note:

Send

Someone would find that motor useful if nothing else. Everything is parts!

PEP - BB100 Badge (verified skill)
Skill verified by gir bot

John F Dean

master steward

Posts: 8738

Location: southern Illinois, USA

3622

I like...

posted 9 months ago

4
Number of slices to send:

Optional 'thank-you' note:

Send

Hi Les,

I played with the chain break. It is not just that the chain won’t move … no lights, indicators, come on at all. It doesn’t recognize that the batteries are in it.

I figure if someone from the future hasn’t tried to stop me, I can’t be messing up that bad.

Hugo Morvan

gardener

Posts: 1258

Location: France, Burgundy, parc naturel Morvan

616

I like...

posted 9 months ago

2
Number of slices to send:

Optional 'thank-you' note:

Send

Did you take the security brake off. That thing on top you push close with your wrist?
I've seen people go ape-shit trying to start it and then it was just that simple security.

Creating edible biodiversity and embracing everlasting abundance.

Rico Loma

pollinator

Posts: 603

posted 9 months ago

6
Number of slices to send:

Optional 'thank-you' note:

Send

My battery chainsaw is not a quality buy like Makita, but I had similar situation once. I tried everything I could, yet no joy.
but one last guess worked. Brought it inside and parked it near the woodstove and over a few days it was warmed slowly.....then started working again. Still working today. I reckon I had inadvertently allowed moisture to seep in over time, now I keep all saws in the driest spot possible to avoid that pratfall

May the battery spirits bring you luck , friend

John F Dean

master steward

Posts: 8738

Location: southern Illinois, USA

3622

I like...

posted 9 months ago

5
Number of slices to send:

Optional 'thank-you' note:

Send

Hi Rico,

Great point! The saw has been under shelter but in unheated areas. I will give it a try.

Oh yeah, that quality buy was “free”. I had a part time job where I traveled a great deal. The pay was poor, but the travel points I accumulated ended up being in the millions. They furnished this homestead.

I figure if someone from the future hasn’t tried to stop me, I can’t be messing up that bad.

R Scott

pollinator

Posts: 4304

Location: Tennessee 7b

366

posted 9 months ago

7
Number of slices to send:

Optional 'thank-you' note:

Send

Does it have the safety “on” button? That membrane switch gets wet easy from condensation. It seems to be the weak link in all the newer Makita. I think it is usually a relatively inexpensive part to replace.

"You must be the change you want to see in the world." "First they ignore you, then they laugh at you, then they fight you, then you win." --Mahatma Gandhi
"Preach the Gospel always, and if necessary, use words." --Francis of Assisi.
"Family farms work when the whole family works the farm." -- Adam Klaus

John F Dean

master steward

Posts: 8738

Location: southern Illinois, USA

3622

I like...

posted 9 months ago

5
Number of slices to send:

Optional 'thank-you' note:

Send

I have had it in the house for a while. It lights up, but it doesn’t run. Yes, I checked the chain break.

I figure if someone from the future hasn’t tried to stop me, I can’t be messing up that bad.

Les Frijo

Posts: 254

posted 9 months ago

6
Number of slices to send:

Optional 'thank-you' note:

Send

John F Dean wrote:I have had it in the house for a while. It lights up, but it doesn’t run. Yes, I checked the chain break.

Interesting! That would suggest the condensation theory. Maybe more time inside will lead to more functionality. Sounds like a design flaw to me. Maybe worth trying to contact someone at Makita and see what they say.

FFS

John F Dean

master steward

Posts: 8738

Location: southern Illinois, USA

3622

I like...

posted 9 months ago

4
Number of slices to send:

Optional 'thank-you' note:

Send

Hills,
If a day or so in the house has gotten some results, I figure I will keep on drying it out through the weekend.

I figure if someone from the future hasn’t tried to stop me, I can’t be messing up that bad.

John Weiland

pollinator

Posts: 2957

Location: RRV of da Nort, USA

934

posted 9 months ago

6
Number of slices to send:

Optional 'thank-you' note:

Send

Les Frijo wrote:

John F Dean wrote:I have had it in the house for a while. It lights up, but it doesn’t run. Yes, I checked the chain break.

Interesting! That would suggest the condensation theory. Maybe more time inside will lead to more functionality. Sounds like a design flaw to me. Maybe worth trying to contact someone at Makita and see what they say.

John, I'm going to assume that you have pulled on the chain to rotate the chain and the cog wheel around a few times?.... I ask because I have two more legacy corded Makita tools, a drill and an angled buffing tool, that also sit for months, sometimes years, without use in an unheated garage with humid summers and frigid winters. This past summer I need the angle tool and it would not run when I activated the trigger. After several rounds of adjusting the speed control and rotating the head by hand, it finally started running and ran fine after that. But I'm wondering now as others have stated about the condensation possibility. Just a thought...

“The most important decision we make is whether we believe we live in a friendly or hostile universe.”― Albert Einstein

Mart Hale

pollinator

Posts: 1238

350

I like...

posted 9 months ago

3
Number of slices to send:

Optional 'thank-you' note:

Send

If it is under warranty appears that the controller board can go out...

https://www.youtube.com/watch?v=AnUpcmSxpOU

Life on a farm is a school of patience; you can't hurry the crops or make an ox in two days.
Henri Alain

I agree. Here's the link: http://stoves2.com